For your safety, the battery door will not close until all 3 batteries are inserted.Ĩ. On the opposite side of the batteries and replace the screws. Push down the small latch at the bottom of the battery compartment so that you can insert the last battery and properly close the battery door.Ħ. Negative "-" ends of the batteries with the markings in the battery compartment. Using a Philips screwdriver, unscrew the 2 screws from the battery door. This will help make sure you've replaced the batteries correctly.Ĥ. Press the Nest button twice to test your Nest Protect. Turn the power back on at the breaker box.ġ0. With the notches on the bottom of your Nest ProtectĪs a guide, place your Nest Protect against its backplateĪnd turn it clockwise until you feel the backplate grip.ĩ. It will click into place.įor your safety, the battery door will not close untilĨ. Negative "-" ends of the batteries with the markings in the battery compartmentĦ. Replace all of the batteries with new Energizer Ultimate ![]() Push the battery door button in the direction of the arrow.ĥ. Remove your Nest Protect from its backplate. Turn the power to your Nest Protect off at the breaker box.Ģ. You can also check the battery life of your Protect at any time.ġ. When the batteries are very low, your Protect will chirp until the batteries are replaced.You’ll get a message during Nightly Promise.Protect’s light ring will pulse yellow when you turn off the lights at night.How to tell when Protect needs new batteries Wired Protects will use backup batteries if there’s a power outage. Protect (Battery) requires 6 AA batteries. Protect (Wired) requires 3 AA as backup batteries. Don’t place new batteries in with old batteries.Using other types of batteries than the ones recommended by Nest will be detrimental to the smoke and CO alarm operation.If you do, they will quickly drain and will need to be replaced soon after installing them. Protect requires lithium batteriesīoth battery and wired Protect require Energizer Ultimate Lithium AA (L91) batteries.ĭon’t use rechargeable or alkaline batteries. Troubleshoot when Nest Protect batteries seem low during setup. Note: If you’re adding your Protect to the app and you get a notification that the batteries are low, the voltage may have temporarily dropped. Follow the steps in this article to learn how to replace them. It could cause losing connection on your lock.When it’s time to replace your Google Nest Protect’s batteries, it will chirp continuously until the batteries have been replaced. Since mesh Wi-Fi points tend to change Wi-Fi frequency (from 2.4 GHz to 5GHz vice versa). If all else fails, pair your Connect to the main Wi-Fi access point instead of the mesh Wi-Fi point.Restart your modem or router, unplug it from the power outlet, wait for 1 to 2 minutes. ![]() ![]() The recommended router settings are the 2.4 GHz Wi-Fi frequency. Keep holding down the button, when the light flashes yellow then goes off, release the button. ![]() Hold your Connect’s button for much longer than 8 seconds, the light will turn yellow, which means your Connect is preparing to factory reset. Hold down Connect’s button until the light pulses blue (about 10 seconds).Wait a few minutes to check if your lock comes back online. Put the batteries back in after 60 seconds.Don't use rechargeable batteries with your lock. If you received a low battery alert, use a fresh set of standard AA batteries. Take off the battery cover and remove the batteries from your lock.Here are some troubleshooting steps you can try: Let’s see what’s going on - a few questions: what’s the status light of your Nest Connect? How far is your Nest x Yale Lock and Connect from the router? Are the batteries of your lock fresh and standard AA alkaline batteries? Also, what Wi-Fi frequency band do you try to connect to (2.4 GHz or 5 GHz)?
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |